Creativity | drafting | RTW Copies | Sewing | Sewing for me | Tutorials

Pattern hack – Cowl/hood top

October 24, 2016

I like to look at CAbi for inspiration on new pieces to make.  I like the details, in general, and they tend to have nice finishes.  I have a friend that invites me to her parties, and I usually end up buying a few pieces that fit into my wardrobe.

This casual top caught my eye this time:

cabi-playground-pullover

It is a deep cowl (about 12″) that transitions into a hood.  It is a nice piece, but I knew I could make it much cheaper than the price they were charging.  It was a pretty simple hack, too.

The top pattern I used here for the base is the Wardrobe by Me Builder T-shirt, which I sized up by one size to make it a looser fit.

The first top I did, I learned a good lesson with it.  Don’t use a poly knit that has a definite right side and wrong side.  You need a knit that is hard to differentiate the front from the back, or where you don’t mind the wrong side color.

After making this first one, I realized my pattern was too shallow for the hood part.  I also didn’t do the thumb-holes or tie waist.  I just wanted to get a muslin completed.  It was wearable, at least.

I do like how this second one turned out.

c-_users_stacy_pictures_pictures_2016_10-october_20161023_20161023_1706

20161023_1715

Here is the add on I made to the basic pattern.  The neckline I used was the medium scoop boatneck.  Here are my hand-drawn pattern pieces for the hood and cuffs.  I wrote on the main hood piece the hood binding measurements, so don’t miss that piece.

hood-pattern

Fabric is from Joann’s. I uploaded my Silhouette Studio file for the shirt design to my Google Drive folder.

  1.  Sew your shirt up (shoulder seams, attach sleeves, sew up the side seams), leaving the neckline edge raw.
  2.  Sew the front and back cowl/hood pieces together.

20161022_1571 20161022_1572 20161022_1573

3.  Top-stitch the seams.  I just used a long straight stitch and pull it while I stitch it, so it has some stretch to it.

20161022_15754.  Sew the ends of the binding together and attach to the hood, with the seam in the middle top of the hood.

20161022_1579 20161022_1580 20161022_1581

5. Press the stitching down towards the inside of the hood and topstitch.

20161022_1582 20161022_1583

6.  Turn the binding inward in half and then over the seam.  Pin and topstitch.

20161022_1585 20161022_1586 20161022_1587 20161022_1589 20161022_1590 20161022_1591

7.  Mark the midde front and middle back of the shirt neckline and cowl.  Clip together at these spots and pin the rest together.  They should match fairly close.  Sew together.

20161022_1593 20161022_1594

8.  Pin the bottom hem 1.5″, sew up the hem, leaving an opening to add elastic.  Put in the elastic, and close up the hole.  I measured the elastic on my high hip to determine a comfortable length.

20161022_1608 20161022_1610

9.  The thumbhole cuffs are hard to explain, so see this tutorial if the pictures don’t make sense.  First you sew up the side seams on the cuffs.

20161022_1595

10.  Have one cuff edge inside out and one right side out and fit the corners together.  You can use a needle and thread to sew in the corners and pull them together.  Baste them down, so they won’t move.  Sew just inside the seam to catch the edge, and stitch a few lines 0.5″ down.

20161022_1597 20161022_1599 20161022_1601 20161022_1602 20161022_1604

11.  Place the side seams together, matching them carefully, and pin.  Sew down from the hem, along the seamline for 1.5″ (I did 2″ here and it was a little tight). Make sure to back-tack and secure the seams.

20161022_1596 20161022_1603

12.   Turn right side out.  One side will generally look better, so choose that one for the outside. Pin the cuffs to the ends of the sleeves and attach.

20161022_1605 20161022_1607

All done!

Comments are closed.